We specialize in Water Towers Industrial Tanks & Logos
High Rise Buildings - Chemical Plants - Factories . Casinos 
Office Structures - Theme Parks Custom Cars
Structural Steel -   Industrial Pipes  - Silos & More

1 - 877-749-5554    pat@greatwesternpainting.com


Acrylic Texture
Anti GraffitiArizona
Arizona Tank Painting
Bad Paints & Effects 
Business Friends
California Tank Painting
Clarifier Tank Painting
Custom Car Painting
Electrostatic Painting
Factory Painting
Fire Proof Painting
Free Gifts
High Rises
Grain Elavators
Hospital Painting
Ind. Paint Manufactures
Industrial Pipe Painting
Industrial Tanks
Lead Encapsulation
Light Pole Painting
Luminescent Paint
Montana Tank Painting
MSHA Certified
North Dakota Tank
Paint Dealers
Safety  & Fall Program
Sand & Hydro Blasting
Shale Gas Fraking
Shot Blasting
Silo painting
Site Map
Structural Steel Painting
Surge Tank Painting
Tank Painting
Texas Tank Painting
Thermal Painting
Utah Tank Painting
Vinyl Wall Covering
Water Tank Inspections
Water Towers

*Lead Encapsulating

Lead Base Paint Encapsulation
EPA Approved Green Products
Water Towers - Industrial Tanks - Bridges - Structural Steel - Barges - Bulk Heads
  Including Thermal Coatings


It is very costly to remove lead base paint from Towers, Bridges, Silos, Structural Steel.

Picture above shows non containment and look how sandblasting causes a dust cloud.
 It can travel for miles

(  If  lead paint was on this project. full containment would cost about $135,000)
(It had a non lead coating)

Our products we use are patented encapsulation coating that acts as a full containment covering.

This moisture cured polyurethane coating has been used successfully in the harshest environments; chemical fields, oil fields and rigs, and in areas that demand resistance to the corrosive effects of day to day exposure. 
And is tested to encapsulate toxic elements such as existing lead-based paint, asbestos,
 rust and other bio-hazard materials.

With minimal preparation and no white sand blasting of the surface required, Our products we use  penetrates deep into and seals the pores of the surface. can protect and seal surfaces of steel, aluminum, concrete, wood, fiberglass, and many other substrates. It will seal out moisture and air with a permanent membrane and block chemical pollutants that cause corrosion and deterioration.


*Rust Grip is a one-part, moisture-cured polyurethane
that can be used as a primer, topcoat or encapsulant.
It can be applied to metal, concrete,
masonry and wood.

Aqua Pox is a two-part water-based epoxy designed
to perform after curing to the same toughness
as solvent-based epoxy formulas.

Enamo Grip is a two-part, aliphatic polyurethane
enamel that forms a uniquely hard and durable
coating film. This self-leveling coating is resistant
to water, acids, solvent and impact. Enamo Grip
is a one-coating system. Enamo Grip can be applied
to metal, concrete, masonry and wood.

Epoxotherm is a two-part epoxy coating which
produces a hard, yet semi-flexible coating film that
will have insulation value equal to or greater than
four inches of batt insulation. This epoxy coating
has four ceramic compounds built into the formulation
to reflect sunlight and to slow conduction
from radiant heat sources. It was designed for use
underwater or in areas where constant splashing
or condensation is a problem. Epoxotherm is resistant
to chemicals and solvents, and can be applied
to metal, concrete, masonry and wood.

The normal epoxy primers cover over Rust
The Encapsulating Coating we use does more then cover up rust.

 & it penetrates into metal surface becoming part of the structure  penetrating in to
the surface of the metal itself.

See Photos of Rust Grip  



 Fisi Bond Specs   1      2   








Stop Rust, Encapsulate you lead paint,  Save Money
 Paint Encapsulation

EPA and Lead Poisoning in Children

Lead poisoning is one of the most serious environmental health hazards to children, particularly for children under the age of six.

 Elevated blood lead levels can impair a young child's mental and physical development. Adults exposed to high levels of lead,

usually in the workplace, are also at risk.


Rust Grip® More Info
Seal virtually any surface and protect it against corrosion, weather and physical wear with Rust Grip®, a three-coats-in-one system that acts as a primer,
intermediate, and top coat with a single application.
Rust Grip® is a metallic-based, moisture-cure polyurethane encapsulating coating designed to coat and seal air, moisture and chemicals out of surfaces.

Rust Grip® stands up to acids, salts and caustic materials with no loss of strength. For EPA VOC standards, Rust Grip® falls under the metallic pigmented coating category. Rust Grip® is 414 grams/liter VOC. (Current California and US National limit of 500 grams/liter). Some additional benefits of Rust Grip® include:
Fast Working – Begins its cure cycle within an hour, penetrating and swelling to seal surface pores. It’s very important to understand that the Rust Grip®

film will anchor itself into the surface of the existing rust, metal or concrete, etc. It encapsulates the surface to have the existing rust become a layer of

 steel over the surface to the 6180 psi strength.Versatile – Protects steel, aluminum, concrete, wood, fiberglass and lead-based paints. Excellent

for minimally prepared surfaces.Class-A Fire Coating – In case of fire, helps to prevent spread of, and will not contribute to, the burn. ASTM E84:
Flame Spread of 5.Strong and Lastin



Read More on Lead Base Paint Abatment Encapulation  Page
Or Read PDF



Lead Abatement Certified     Certified Leed Green      Lead Encapsulation

Lead Base Paint Encapsulation

1 - 877-749-5554



Full Service Commercial & Industrial Painting Contractor

Rust Grip SUPERIOR STEEL INTERNATIONAL, LLC Sammy Kempton (970)985-0209 Fax(970)243-0853 skempton68@msn.com Website: www.spicoatings.com Duns: 611247342 Cage: 6NKN9